Search the whole station

How to Calculate Output Per Minute for Carpet Backing Foaming Production Line

Wenzhou Feilong Polyurethane Equipment Engineering Co., Ltd.
Chinese website: http://www.pumcn.com/
English website: https://www.flpumachine.com/

When launching new lines, switching product specifications or adjusting line speed, most manufacturers of polyurethane carpet backing encounter the same question: what is the proper material output per minute for the foaming line?

Output flow is not an arbitrary setting value. It is closely linked with carpet travelling speed, backing thickness, foam density and fabric width. Excessive output leads to over-thick backing, overflow and material waste. Insufficient output causes thin backing, material shortage and bare substrate, resulting in rejected products.

Carpet backing adopts continuous coating and foaming process, which is different from intermittent casting machines with discrete pouring. It follows a standardized calculation method. Combining actual production conditions, we explain the formula, calculation example and common pitfalls below.

How to Calculate Output Per Minute for Carpet Backing Foaming Production Line - BrazilExhibition(images 1)
1. Core Calculation Formula
Total mass output per minute (kg/min) = Carpet width (m) × backing thickness (m) × foam density after curing (kg/m³) × carpet line speed (m/min)
Notes:
1.1All units must be consistent; thickness needs to be converted into meters. Use the density of finished foamed foam instead of liquid raw material density.
1.2The calculated result is the weight of cured foam produced every minute.
1.3Divide the total flow into A component and B component flow according to the mixing weight ratio.
1.4This formula applies to indirect coating and film transfer coating for continuous PU carpet backing.
2. Explanation of Parameters
2.1Carpet width: effective foaming width of finished backing, unit m, e.g. 1.25 m
2.2Backing thickness: thickness after foaming and curing, unit m. Typical carpet backing thickness ranges from 3 mm to 4 mm, equal to 0.003 ~ 0.004 m
2.3Foam density: density of finished flexible PU foam, commonly 200 ~ 250 kg/m³ for carpet backing
2.4Carpet line speed: travelling speed of carpet on the line, unit m/min
Note: Many suppliers mark line speed in m/h, divide by 60 to convert into m/min before calculation.
How to Calculate Output Per Minute for Carpet Backing Foaming Production Line - FeilongPolyurethane(images 2)
3. Practical Calculation Case
Standard carpet backing parameters for example:
Width: 1.25 m
Backing thickness: 3 mm = 0.003 m
Foam density: 220 kg/m³
Line speed: 3 m/min
Calculation:
Output per minute = 1.25 × 0.003 × 220 × 3 = 2.475 kg/min
Total mixed flow of A+B material should be stably kept at 2.475 kg per minute.
If the weight ratio of A to B is 100:80
A component flow = 2.475 ÷ (100+80) ×100 = 1.375 kg/min
B component flow = 2.475 ÷ (100+80) ×80 = 1.100 kg/min
Calibrate metering pumps according to these target flow rates, together with temperature control and vacuum adjustment to stabilize foaming performance.
If the required thickness changes to 4 mm, recalculate and increase output accordingly, otherwise the finished thickness will fail to meet requirements.
4. Four Common Calculation Mistakes
❌ Mistake 1: Use liquid raw material density instead of cured foam density Liquid raw material density is much higher than foam density. Using this value will get an overestimated flow, causing heavy material waste. Always use finished foam density in the formula.
❌ Mistake 2: Unit inconsistency, input thickness in mm directly Inputting 3 mm directly without converting to 0.003 m will magnify the result 1000 times. This is the most frequent error on site.
❌ Mistake 3: Ignore density change caused by inorganic fillers After adding calcium carbonate or other fillers, foam density rises obviously. If you keep using density data without fillers, calculated flow will be insufficient and backing will be too thin. Re-measure density once filler dosage changes.
❌ Mistake 4: No adjustment margin reserved after getting theoretical value The theoretical value is for ideal conditions. Metering pump accuracy, temperature and raw material viscosity bring minor fluctuations. Reserve an adjustable range of ±10% for on-site fine-tuning of thickness.
How to Calculate Output Per Minute for Carpet Backing Foaming Production Line - FEIPLARFEIPUR2026(images 3)
5. Commissioning Tips after Flow Calculation
5.1Set metering pumps according to theoretical flow first, run small batch trial and measure backing thickness.
5.2Too thick: reduce A and B flow synchronously. Too thin: increase flow synchronously.
5.3Acceptable thickness but poor foaming: do not only adjust flow; check mixing ratio, material temperature and mixing quality first.
5.4If line speed increases or decreases, output flow must change proportionally. Line speed and material output are positively correlated.
5.5Regular recheck: re-test foam density and recalculate flow when raw material batch, filler ratio, ambient temperature or humidity changes.
6. When You Need to Recalculate Output Flow
Change backing thickness specification
Adjust production line travelling speed
Modify formula, increase or reduce filler content
Change required foam density
Recalibrate after overhaul or metering pump replacement
Closing:
Calculating output for carpet backing foaming line is essentially volume multiplied by density and matched with line travelling speed. The formula itself is simple; the key is consistent units and parameters matching your real production formula. Unstable backing thickness often comes from mismatched flow and line speed.
Wenzhou Feilong Polyurethane Equipment Engineering Co., Ltd. can calculate metering configuration for your carpet backing foaming line based on your width, thickness, density and line speed requirements. We provide solutions for indirect coating and film transfer carpet backing production lines.
The prev: The next:
Expand more!

WhatsApp Me
Send Message
[email protected]